Showing posts with label Kinks. Show all posts
Showing posts with label Kinks. Show all posts

2017-05-27

Drilling Holes in all the Right Places



There are 2 common ways to drill accurately placed holes: floating or indexed.

The floating method:
  1. Layout the part, scribing lines to the accuracy desired.
  2. Prick punch (a fine 30-50deg punch) the scribed intersections. Done correctly, you should be able to feel the intersecting lines with the point of the punch but use a magnifying glass to confirm. An optical center punch is another option here, but again confirm.
  3. Drift the center mark as necessary until it is at the line intersection.
  4. Enlarge the mark with a center punch.
  5. Optionally, with a divider using the center punch mark as an anchor, scribe witness circles the same or slightly larger diameter than the desired hole.
  6. Select a very small drill with a tip that fits properly in the center punch mark. Some people prefer to just make the center punch mark larger than the web of the pilot drill they intend to use.
  7. Drill while allowing the work to float on the drillpress table such that the drill will align with the punch mark.
  8. Select the next drill, which should have a web thickness smaller than the original hole or punch mark and have a diameter slightly larger than the web thickness of the final or, if necessary, intermediate drill.
  9. Drill the final size.

The indexed method:
  1. Clamp and index the part to a known feature. If you index off a punch mark, use an appropriate measuring tool to pick up the mark.
  2. Crank the table to the desired hole location. If using a drillpress, you can index each hole to drill.
  3. Use a short spotting drill or, if it's all you have, a center drill.
  4. Drill to the web thickness of your final drill.
  5. Drill to final size.

General notes:
  • The floating method relies on a moving work-piece and flexing drill to align with a center punch mark. Horizontal rigidity is bad. Do not clamp down the vice or fixture and use jobber length drills. When drilling large holes, remember drill safety and consider indexing instead.
  • The index method relies on rigidity. Clamp and lock everything down. Use stub-length drills where possible. Use spotting drills if you have them.
  • Mixing the two approaches, using stub-length drills when floating to center punch marks for example, will give less accurate results.
  • Layouts on work to be clamped down and indexed will help with error checking but a center punch mark will not, in itself, correctly line up the drilled hole. It's up to the operator to correctly index to the mark.
  • When using the floating method, if the initial hole has gone off center then you can drift it back a slight amount. Use a cold chisel to notch the far side, the side you want to move away from, and then drill the next size up drill available, possibly repeating several times. Witness circles help with this approach.
  • When using the index method, if the initial hole has gone off center then you can re-index and use an endmill or, if large enough, bore it back.
  • If holes in multiple parts are to align, bolt, clamp, or even tack weld them together and drill all at the same time. Another option is to make a drill guide (jig) that is then clamped to each part in turn.
  • The tables on light-duty drillpresses will often flex down with drilling pressure, thus going out of square. For this reason, deep holes are best done on more rigid machines. If necessary on a light-duty drillpress, block the table up to reduce flex. Optionally, shim the work on the table to compensate for the expected flex for the drill pressure being used.
  • Tramming the table is also important on deep holes.
  • A poorly sharpened drill can drill oversized holes.
  • Accurately sized holes require reaming or boring.
The above is the received wisdom learned from various posters and topics on the Home Shop Machinist forum, as well as other places.

2016-12-19

Notes on Using Epoxy Primer

Never used this stuff, but the information is worth filing away for when the day comes.

Note that epoxy primer seems to be a great way to prevent rust on bare metal, something regular primer does not do (and I can confirm that).


Mostly an original quote, but with a little reformatting to make it easier to read.

From: Radkins from the Home Shop Machinist forum, here.

Epoxy primer is great stuff and the first thing I do to any body panel or repair is to spray it with epoxy primer, the stuff is expensive but it can't be beat for corrosion protection!

A couple of tips for using this type of primer:

  1. It needs a rather rough surface to adhere properly. I scuff the bare metal with 180 grit paper and then apply two coats allowing it to become dry to touch before applying the second coat. If a finish is not applied within a day or so, this varies with brands, it will need to be scuffed with sandpaper and another coat applied before any topcoating is applied including conventional primers.
  2. If left for any length of time then it should be topcoated with another primer such as lacquer or one of the polyester filler primers. No scuffing needed if coated within a couple of hours. If left for weeks, never mind years, it becomes EXTREMELY hard making it very difficult to sand and causes difficulty in getting topcoats to adhere. If something like even simple lacquer primer is applied around two hours after the original application it will adhere quite well and is then easily prepped for painting even after being left for long periods of time, old uncoated epoxy primer however is a absolute nightmare to properly prep for finish painting!


Oh, and he follows up with this:  (something else I learned today).

NO, DO NOT SANDBLAST BODY SHEETMETAL!!!!! A sandblaster will warp most sheetmetal body parts beyond any hope of repair! I don't mean "Aw s#!* now I am going to have to fix that", I mean toss it in the scrap and buy new parts kind of ruined. Some parts that are stiff and well supported like door posts and some firewalls may be blasted ok but fenders, hoods, trunk lids, etc will be instantly distorted way beyond any repair. Those sand particles act like millions of tiny peening hammers and will distort the surface of the metal due to the uneven stretching (and no, heat has absolutely nothing to do with it despite the common misconception so keeping the parts cool is futile!). While it can and has been done successfully the blast operator has to REALLY know his stuff and even then it's highly risky.

2016-11-24

Turning a Radius



A neat way to mill a radius on something with a through hole.  Just put a pin in the hole, rest the pin on the top of the vice jaw, and then rotate, clamp, and cut repeatedly.

2016-07-17

Turning the End of a Big Bar

Say you need to turn the end of a bar that is too big to go through the lathe headstock and too long to fit between centers (or the center-rest if you have one)...

Here are some answers:

Arcane suggests:  If you have a milling vise setup that attaches to the cross slide for your lathe and a boring head with a MT3 taper, clamp the shaft in the vise, center it on the spindle and then use the boring head to reduce the end.

Dan suggests:  There was someone who did an interesting trick. They welded a smaller piece to the end and chucked it up. Supported the far end in a steady rest. Then they turned down the original bar and parted it. Rotate and repeat.

Better yet, just start with stock longer than required an part off the chucked bit.

My idea, specific to my 3in1 machine:
Using something of suitable height, like the angle table (level, just for the height), make a vertical clamp that hangs outboard the lathe.  Swing the head over to match and lock down, then use the X/Y to center.  Once centered, use the boring head as above, with the cutter pointing inward.  This would give me about 4' of length, and it would be easier to set up than removing the tailstock to use the lathe spindle.

2016-07-10

Making SS Springs

Interesting post on HSM by Dorn:

Using annealed stainless steel wire (aka safety wire) that is not springy in this state, it can be work-hardened by stretching.  Once work-hardened, it can be wound into a spring.

Rich added:

I also use a "Drawing" technique when I want smaller wire for a model or repair application.  I open my vise about 4 or 5 inches and then wrap the wire around the jaws ( 2-3 wraps ).  Now I open the jaws more and draw the wire down to a smaller size with out having the use my legs or arms, only the vise leadscrew.

Never tried it... but it's something to keep in mind for when that someday comes along.

2016-03-25

Flexture Clamps

Idea from a Dan Gelbart video (Building Prototypes, part 13):

If you want to clamp something, cut a slot near it, then drill in the middle of the slot, then tap the hole for a pipe thread.  When threading in a plug, the taper will expand the slot, which will move the metal to clamp the part.


2015-11-23

New Directions

So, I've decided to start a new experiment.  I like reading about workshop tips and tricks, 'kinks' as they used to be called, and I've read a lot of them.  So many, in fact, that I don't remember anywhere near half... seems the good ideas spill out faster than I put them in these days.  I'm forgetting so many it's starting to bother me.  Thus, I've decided to write them down. 

After some consideration I came up with a basic criteria list: I want the ideas to be easy to enter, I want them accessible from any web browser, I want them to be backed up to the cloud, and want to be able to put in tags for easy searching.  From that, and considering that I don't really care if anyone else makes use of them, a blog seems about the right tool.

Thus, hopefully as long as I can keep learning, I'm going to be putting tips and tricks in this blog.  They generally aren't mine, and I'll try to cite where I can.  If anyone find them useful, so much the better.  I don't mind sharing my aggregation efforts.